7
Error messages and
advice
1.800.561.8187
3D Disto, Error Messages
Error No. Advice
150
Working range was exceeded.
151
Invalid measurement.
152
Change the 3D Disto position or use ruler for offset points.
160
Repeat and do not move the ruler between both measurements.
161
In some cases the Offset Point tool can not be used.
170
Restart 3D Disto if the problem persists.
171
Check all devices, for example power supply or cables, and try again.
240
Tilt sensor calibration was not successful. System accuracy is at risk.
Contact your distributor or Leica Geosystems representative.
241
Too much drift. Repeat calibration precisely.
243
Set up the instrument stably. Do not touch or rotate the 3D Disto. Repeat
calibration.
300
Select a horizontal line.
350
Check projection surface. Laser could not reach the correct position.
755
Point cannot be measured. Try different position. Tool does not work on
horizontal planes.
760
Point cannot be measured. Enter different values. Tool does not work on
horizontal planes.
765
Point cannot be measured. Try different position or enter different value.
Tool does not work on horizontal planes.
800
Data import or export is not possible.
801
Not enough memory on USB stick.
802
Storage device does not work properly.
803
Check file condition and content.
804
File or Folder write-protected or damaged.
900
3D Disto error. Contact your distributor or Leica Geosystems representa-
tive if the error repeats.
901
The reflected laser signal is too low.
902
The reflected laser signal is too high.
903
Too much background light.
904
Laser beam interrupted. Repeat measurement.
950
Execute Location Check to retain accuracy!
951
3D Disto tilt is over 3°. Set up horizontally!
952
Check 3D Disto, check for obstacles interrupting WLAN connection, or
move towards 3D Disto.
953
Check connection and cable.
954
Plug in cable or choose «WLAN» in the menu.
955
3D Disto temperature out of working range.
956
Too much vibration or permanent movement.
998
Contact your distributor or Leica Geosystems representative.
999
Contact your distributor or Leica Geosystems representative.
www.
information@itm.com
.com
62
|
Error Code
|
Description |
Corrective Measure |
|
154 |
Transverse tilt >20° |
Hold the instrument without any transverse tilt |
|
156 |
Transverse tilt > 10° |
Hold the instrument without any transverse tilt |
|
160 |
Main tilt direction, angle too high (>45°) |
Measure angle up to +/- 45° |
|
162 |
The calibration has not been accomplished on a leveled surface and the calibration value is respecitvely within an ineligible area. |
Calibrate the device on an absolute horizontal leveled surface. |
|
203 |
Wrong measuring sequence for Pythagoras measurements |
Measure in correct sequence |
|
204 |
Calculation error |
Repeat procedure |
|
206 |
No endpiece detection |
Attach the endpiece properly. If error still occurs, replace the endpiece |
|
217 |
Measuring module error |
Contact Us |
|
240 |
Data transfer error |
Repeat procedure |
|
245 |
2nd button pressed although no Bluetooth connection exists. |
Establish Bluetooth connection |
|
252 |
Temperature too high, above 50°C |
Cool down the instrument |
|
253 |
Temperature too low, below 0°C |
Warm up instrument |
|
255 |
Receiver signal too low, measuring time too long, distance too long |
Use target plate, measuring time > 10 sec. |
|
256 |
Receiver signal too strong |
Use target plate (white side) |
|
257 |
Erroneous measurement, too much backlight |
Use target plate |
|
260 |
Laser beam was interrupted |
Repeat measurement |
|
272-276 |
Measuring module error |
Contact Us |
|
279 |
Measuring module error |
Contact Us |
|
285-291 |
Measuring module error |
Contact Us |
|
297-299 |
Measuring module error |
Contact Us |
|
402 |
Measuring module error |
Contact Us |
|
404 |
Measuring module error |
Contact Us |
|
501-503 |
Measuring module error |
Contact Us |
|
651 |
Measuring module error |
Contact Us |
|
801-803 |
Measuring module error |
Contact Us |
Добро пожаловать!
Войдите или зарегистрируйтесь сейчас!
Войти
-
У меня проблемы с измерениями: при нажатии кнопки ALL или DIST выдает ошибку 255 (будто исходящий сигнал не вернулся). Однако при проведении EDM теста, качество сигнала не ниже 95%, видимость прямая — помех нет. В чем дело, я не знаю..
#1
-
Народ, ну хоть предположения какие-нибудь есть?
#2
-
Форумчанин
- Регистрация:
- 3 июн 2009
- Сообщения:
- 207
- Симпатии:
- 15
- Адрес:
-
Москва
В почту ответил.
Продублирую ответ здесь:Добрый день!
Рекомендуем обратиться в авторизованный сервис.
Возможно, Вам потребуется настройка дальномера или замена платы дальномера.#3
-
Все дело,как оказалось, в плате дальномера… Ремонт обошелся в 35 тысяч рублей…
#4
